Advantech AMAX-4860
8-ch IDI & 8-ch Relay EtherCAT Remote I/O module
- Suitable for EtherCAT networks
- 8-ch Isolated Digital Input and 8-ch Form A-type Relay Output
- High-voltage isolation on input channel (2,500 VDC)
- Quick removable European type connector
- LED indicators for I/O status
- Supports EtherCAT Distributed Clock (DC) mode and SyncManager mode
- Two Rotary switches for up to 256 slave IDs
The AMAX-4860 is an industrial EtherCAT slave module equipped with the EtherCAT protocol. Its compact size and DIN-rail mount kit can install easily in a cabinet. Euro type pluggable terminal blocks and LED indicator help users to maintain and set up their system. All digital input channels are protected by 2,500 VDC isolation circuits.
Compact Size
High density channel count in a compact design helps increase space utilization ratio. Din-rail mounting kit ensures easy installation in cabinets.
Easy to Maintain
Terminal block, LED indicator, Switch and EtherCAT port can be operated at front side. These provide a convenient way to wire, test, debug or maintain. In particular, AMAX-4800 series equip euro type pluggable terminal block to insert wires without screw tools. These features can help user to reduce maintenance cost and time.
Good expandability
Since a total of 65,535 nodes per network segment can be connected, the I/O channel amount will not be limited by PCI/PCIE slot any more. The physics of Ethernet allow a cable length of up to 100 m (300 ft) between two nodes, so expensive signal cable will be replaced. This means less IPC, simpler wiring topology and lower cost.
Synchronization
The synchronization time between each slave module is one of important parameter for motion control. AMAX-4800 series support EtherCAT distributed Clock. By using distributed clocks , modules can calibrate the time difference less than 1 us to output synchronize signal.
Compact Size
High density channel count in a compact design helps increase space utilization ratio. Din-rail mounting kit ensures easy installation in cabinets.
Easy to Maintain
Terminal block, LED indicator, Switch and EtherCAT port can be operated at front side. These provide a convenient way to wire, test, debug or maintain. In particular, AMAX-4800 series equip euro type pluggable terminal block to insert wires without screw tools. These features can help user to reduce maintenance cost and time.
Good expandability
Since a total of 65,535 nodes per network segment can be connected, the I/O channel amount will not be limited by PCI/PCIE slot any more. The physics of Ethernet allow a cable length of up to 100 m (300 ft) between two nodes, so expensive signal cable will be replaced. This means less IPC, simpler wiring topology and lower cost.
Synchronization
The synchronization time between each slave module is one of important parameter for motion control. AMAX-4800 series support EtherCAT distributed Clock. By using distributed clocks , modules can calibrate the time difference less than 1 us to output synchronize signal.
Communication
- Interfac
EtherCAT
Data transfer medium
Ethernet/EtherCAT cable (min. CAT 5), shielded
Distance between modules
Max. 100 m (100BASE-TX)
Data transfer rates
100 Mbps
Configuration
Not required
Communication Cycle Time
200us
Digital Input
- Channels
8
Input voltage
Logic 0: 3 V max.; Logic 1: 10 V min. (30 V max.)
Isolation protection
2,500 V DC
Relay Output
- Channels
8
Relay Type
Form A
Contact Rating (resistive)
2A@250V AC , 2A@30V DC
Max. Switching Power
500VA , 60W
Max. Switching Voltage
270V AC , 125V DC
Resistance
30m Ω max.
Operating Time
Max. 10ms
Releasing Time
Max. 5ms
Life Expectancy
Mechanical 2 x 10 7 ops. at no load.
Electrical 3 x 10 4 ops. @2A/250V AC
General
- Connectors
10-pin 3.81 mm terminal block * 3 (I/O)
3-pin 3.81 mm screw terminal block (power) RJ-45 * 2 (EtherCAT)
Dimensions
120 mm x 120 mm x 40 mm
Operating temperature
-20 ~ 60°C (32 ~ 140°F)
Storage temperature
-40 ~ 70°C (-40 ~ 158°F)
Storage humidity
5 ~ 95% RH (non-condensing)
Power supply
10 ~ 30 V DC
Power Consumption
Typical 85mA @24V; Max. 110mA @24V
Ordering Information
- AMAX-4860-AE
- 8-ch IDI & 8-ch Relay EtherCAT Remote I/O module
96PS-A40WDIN
- DIN RAIL A/D 100-240V 40W 24V
Customers who viewed this item also viewed